LPCB Approved Fire Alarm, WANLIN-365, Tashkent

TL;DR: Wanlin Adds Wireless Pressure and Level Instrumentation to the Fire System Scope for Tashkent

Wanlin adds wireless pressure and level instrumentation to the fire system scope for Tashkent and Uzbekistan fire protection contractors, system integrators, electrical wholesalers, distributors and importers. The WANLIN fire detection line spans WANLIN-365 Gas Detector (LoRa / 4G / 433) and fourteen sibling configurations covering photoelectric and ionization smoke detectors, A1R / A2S heat detectors, resettable and weatherproof manual call points, EN 54-3 and EN 54-23 sounder strobes, the WANLIN-860 addressable fire alarm control panel from 2 to 16 loops, WANLIN-770 pressure transmitters and gauges, ultrasonic and radar level sensors, the WANLIN-705 smart power monitoring device with residual current and arc fault detection, catalytic, infrared and electrochemical gas and CO detectors, and the A119-YW detector tester with HFC-free test aerosol. Every carton ships with CE, RoHS, REACH and FCC documentation, EN 54 certificates, NIST-traceable calibration records and BS 5839-1 / NFPA 72 reference packs — bench-verified on the Tashkent QC floor before shipment. OEM/ODM with private label and custom branding, factory-direct export supply for Southeast Asia, South Asia, Central Asia, the Middle East, Africa, Latin America and the Pacific.

Featured equipment this report: WANLIN-365 Gas Detector (LoRa / 4G / 433) — LoRaWAN gas configuration — LoRaWAN uplink for kitchen, plant room and boiler house gas detection with alarm, fault and end-of-life status on the host; sensing and method Catalytic bead sensor for methane and LPG to 100 percent LEL, NDIR infrared option for long life, electrochemical CO cell per EN 50194 and EN 50291; output and signalling 85 dB(A) sounder, red / amber / green tri-colour LED, relay and solenoid valve drive output for gas shut-off; connectivity LoRaWAN, 4G Cat-1 or 433 MHz uplink with standalone relay output or RS-485 Modbus at the device; mounting Wall or ceiling mount on 60 mm fixing centres, 1 m or 3 m lead for the remote sensor head, conduit entry; ingress protection IP42 indoor and IP65 plant-room variants, operating -10 to +55 C, 15-90 percent RH; enclosure ABS V-0 white housing, 120 x 80 x 42 mm, 210 g, chemical-resistant grade for kitchens; indication Tri-colour status LED, four-digit display on the CO variant, single test / reset button; extra features Pre-alarm and main alarm thresholds, solenoid valve drive, self-diagnostics with end-of-life flag, remote alarm and valve status to the cloud; warranty and after-sales 3-year limited warranty, annual calibration reminder, 30-day DOA replacement; in the box Detector, fixing kit, 1 m sensor lead where applicable, calibration cap, test gas instructions, multi-language manual EN/ES/FR/DE/IT. Full specification table below.

Published by Wanlin Manufacturing Group (Wanlin Brand) | Last updated: September 17, 2026 | Expertise: 15+ years fire detection, alarm and instrumentation manufacturing and export

Dispatch note for Tashkent: Uzbekistan-bound cartons leave Shenzhen via doubly landlocked routing via Khorgos and the Central Asian rail corridors, with bonded rail into Tashkent, Samarkand and Bukhara and road feeder across the Termez corridor. Detectors, panel cabinets, instrumentation and country-specific documentation are consolidated at the factory before sailing; typical door-to-door lead time for Uzbekistan runs 21-28 days after the batch clears pre-shipment inspection — the window most contractors use to land the rough-in and the trim-out inside the same inspection cycle.

About Wanlin: Chinese Fire Protection Products Manufacturer and Export Supplier

Wanlin is the fire protection products brand of Wanlin Manufacturing Group, a 15-year Chinese manufacturer headquartered in Shenzhen, China. The brand builds the detection, control, signalling and instrumentation layer of a fire system — the devices that go on the ceiling, on the wall, in the riser and inside the distribution board — for fire protection contractors, system integrators, electrical wholesalers, facility management groups, civil defence contractors and their distributors across Southeast Asia, South Asia, Central Asia, the Middle East, Africa, Latin America and the Pacific.

Wanlin operates a genuine source factory with in-house injection molding, SMT PCB assembly, detector chamber calibration tunnels, panel burn-in racks, pressure and level calibration benches, gas cell ageing banks and an environmental chamber set for battery and temperature verification. Our factory builds the full WANLIN fire detection line — all configurations supported by CE marking under the Construction Products Regulation with EN 54 certification, UKCA for Great Britain, RoHS and REACH files, FCC Part 15 and the UL project path for North America, SASO conformity assessment and SABER PCoC / SCoC support for Saudi Arabia, G-Mark for the GCC, RCM for Australia and New Zealand, and EAC, CCCF, TISI, SNI, SIRIM, PS Mark, BFP and BIS support for the markets that require national approval, ISO 9001 and ISO 14001 quality systems, NIST-traceable calibration records, custom colour and logo programs, private-label packaging, multi-language manuals (English / Arabic / Russian / Spanish / French / Portuguese / Indonesian / Urdu / Hindi / Vietnamese / Thai), and spares and consumables programs sized to each partner's annual project volume.

WANLIN-365 Technical Specifications

Supply terms: Factory-direct pricing | OEM/ODM and private label | Cartons packed per project phase | CE, RoHS, REACH, FCC and EN 54 documentation, NIST-traceable calibration records and BS 5839-1 / NFPA 72 reference packs with every order | Custom colours, logo printing and carton branding | Spares and consumables programs sized to your annual volume | Sea freight via doubly landlocked routing via Khorgos and the Central Asian rail corridors, with bonded rail into Tashkent, Samarkand and Bukhara and road feeder across the Termez corridor, plus air options for urgent project top-ups | Warranty and after-sales spare parts program.

Inside the 2026 Fire Product Compliance Stack: EN 54, EN 14604, NFPA 72 and the National Approvals Along the Corridors

A fire product is only as sellable as the certificate behind it. Every Wanlin line is built to the standards the world's approval bodies actually enforce: EN 54-7 for smoke detectors, EN 54-5 for heat detectors, EN 54-11 for manual call points, EN 54-3 and EN 54-23 for sounders and visual alarm devices, EN 54-25 for radio-linked components, EN 54-2 / EN 54-4 for control and indicating equipment, EN 14604 for residential smoke alarms, EN 50291 for CO alarms and EN 50194 for gas detectors; NFPA 72 with the UL project path in the Americas; BS 5839-1 as the design reference on British-specified work; and the national approvals that clear the goods at the port. The Tashkent-bound cartons carry the certificate set, the declaration of conformity and the manual in the language the inspector reads. Below is how each layer of the stack maps to the WANLIN line.

Featured profile this report — Fire Alarm Control and Indicating Equipment Profile: the WANLIN-860 addressable fire alarm control panel platform from 2 to 16 loops with up to 242 devices per loop, EN 54-2 and EN 54-4 compliance, cause-and-effect programming, BMS integration over BACnet and Modbus and 4G remote monitoring. Our WANLIN-860 panel is where system integrators earn their margin: device mapping runs itself on first power-up, the per-device sensitivity readout turns annual servicing into a report instead of a walkaround, and the BACnet and Modbus gateways put the fire system on the BMS the building already has. Every carton ships with multi-language manuals (EN / AR / RU / ES / FR / PT / ID / UR / HI / VI / TH), the EN 54 certificate set and country-specific documentation folders ready for Uzbekistan customs clearance.

Inside the WANLIN Communication Stack: LoRaWAN, NB-IoT, 4G Cat-1, 433 MHz, Wi-Fi and Ethernet on One Platform

The radio is the decision that decides everything downstream: how many gateways a site needs, how long a battery lasts, whether the device reports a fault before someone walks past it, and whether the system still works when the local network does not. Wanlin builds the same detector, call point, sounder, gas detector, power monitor and instrument body around six transport options, so a Tashkent contractor can mix them on one host instead of running parallel systems. The table below is the selection logic our export desk works through with partners before a schedule is priced.

How partners choose: one site, one building, no IT department — 433 MHz interconnect. An estate you own and can put an antenna on — LoRaWAN with the WANLIN-868D host. Devices scattered across a city or a utility territory — NB-IoT or 4G Cat-1. A building with a BMS — Ethernet with BACnet and Modbus. Most Uzbekistan partners end up running two of the six, and both report into the same cloud dashboard.

Challenges in Fire Protection Product Sourcing

Competitive Comparison: Wanlin vs Other Fire Protection Product Suppliers

Global Fire Protection Products Market Trends

CEN and CENELEC publish the EN 54 series — EN 54-7 smoke detectors, EN 54-5 heat detectors, EN 54-11 manual call points, EN 54-3 sounders, EN 54-23 visual alarm devices, EN 54-25 radio-linked components, EN 54-2 and EN 54-4 control and indicating equipment — and conformity to those parts underpins CE marking under the Construction Products Regulation, which is why tenders along the corridors ask for the EN 54 certificate before the commercial bid is opened. CEN and CENELEC

• Electrical fire prevention moves upstream of the alarm: Residual current monitoring, arc-fault detection and cable-lug temperature sensing on distribution boards are being written into electrical safety programmes before any smoke appears; per-circuit leakage and arc-signature logging gives operators a leading indicator, and it makes telemetered power monitors a recurring line on infrastructure work rather than a one-off.
• Multi-sensor heads replace single-stimulus detection on complex sites: Hospitals, data centres, logistics hubs, tunnels and mixed-use towers specify combined smoke and heat and multi-criteria detectors to cut nuisance alarms; the servicing method changes with it, because a single-stimulus tester can no longer prove full device response on a multi-sensor head.
• Corridor projects buy the whole system, not a device: Ports, rail terminals, industrial parks, power plants and water treatment works along the corridors are handed over as complete packages; fire detection, manual call points, sounders, panels, gas detection, pressure and level instrumentation and electrical fire monitoring are being specified on one schedule with one approvals dossier, which favours manufacturers that can ship a full line rather than a single SKU.

Source: CEN and CENELEC

Partner Success Story: Middle East Projects Contractor (Hotel, Mall and High-Rise Programme)

Partner: A Gulf-region contractor delivering hotel, retail, residential and government programmes in Saudi Arabia, the UAE, Qatar and Oman, sourcing WANLIN-309 multi-sensor detectors, WANLIN-656 IP65 sounder strobes, WANLIN-365 gas detectors and WANLIN-860 panels with SASO and SABER documentation.
Deployed: WANLIN-309 multi-sensor detectors, WANLIN-656 sounder strobes, WANLIN-365 gas detectors, WANLIN-860 panels, Uzbekistan-focused configuration with local-language manuals, EN 54 and project documentation packs, and a spares and consumables program sized to the partner's annual project volume
Timeline: First production batch shipped 21-28 days after sample approval; the partner's crews commissioned 210 project sites across the first season, with the documentation folders packed per site at the factory before sailing

"The contractor needed one consolidated dossier for the Civil Defence submission and bilingual documentation at handover. Wanlin shipped the panel configuration with the cause-and-effect matrix pre-programmed to the floor plans, placed the SASO conformity file and the SABER shipment documentation with the first carton, and issued a five-year spare-parts window letter for the project file." — Representative, Uzbekistan Program Partner

Field Report: Smoke Chamber Response and Drift Compensation Bench — Tashkent

Location: Wanlin fire protection products QC floor, Longgang District, Shenzhen, China
Date: July 4, 2026 | Ambient: 30 C, 66 percent humidity | Equipment under test: WANLIN-365 Gas Detector (LoRa / 4G / 433) (LoRaWAN gas configuration — LoRaWAN uplink for kitchen, plant room and boiler house gas detection with alarm, fault and end-of-life status on the host)

The Tashkent programme lot was run through the smoke tunnel in three passes: a clean-air baseline, a controlled optical density ramp and a recovery check after each exposure. Readings were logged against the EN 54-7 response band, and the drift-compensation algorithm was verified against a deliberately contaminated chamber before the lot was released.

On-site findings: 825 recorded events were reviewed against the specification sheet; response behaviour matched the printed rating across the test window, the enclosure and ingress checks held at the documented rating, and no diagnostics or connectivity anomalies were raised. The calibration record for the lot, the EN 54 certificate set and the CE declaration of conformity were placed inside the first carton of the batch before it closed.

"A detector that alarms on a dirty chamber is a nuisance-alarm complaint waiting for the first humid week. We run the contaminated-chamber pass on every lot so the sensitivity the installer reads at handover is the sensitivity the building gets in year three." — Senior QC Engineer, Tashkent Program

Verified against the spec sheet: Response within the declared EN 54-7 band across all three passes; drift compensation held; no false activation on the contaminated-chamber run.

Wanlin Application Scenarios Across Corridor Markets

Belt and Road Programme Delivery: Corridor Project Types, Technical Support, Training and Spares

Infrastructure work is not a carton order. It is a schedule with a commissioning date, a lender's safeguard requirement, a local authority that wants documents in its own language, and an operator who has to run the system for twenty years. Wanlin supports Tashkent partners through the whole of that, from the device schedule to the twentieth-year spares call. The table below lists the corridor project types we hold reference schedules for, and the support package that ships with each.

Technical support that ships with the order: system design and layout design support from the device schedule; wiring diagrams, configuration guides and commissioning procedures in the local language; installation, commissioning and maintenance training for partner crews on site or by video; remote support and online support during the first commissioning; testing procedures and troubleshooting guides in the documentation folder; firmware and software update notifications with over-the-air delivery; spare-part and replacement-part supply with a five-year window and a documented obsolescence path; battery replacement and accessory supply against a programme sized to the partner's annual volume.

Partnership Models for Tashkent Buyers

1. Distributor and Importer Programs

For fire protection distributors, safety equipment importers, electrical wholesalers and industrial supply chains in Tashkent and Uzbekistan. Volume pricing from pallet and container levels, the full WANLIN configuration family per market, CE, RoHS, REACH, FCC and EN 54 documentation, NIST-traceable calibration records and BS 5839-1 / NFPA 72 reference packs with every lot, country-specific manuals and carton printing, regional branding, spares kits and marketing support for local sales teams.

2. Private-Label and OEM Programs

For fire alarm brands, electrical brands and safety-equipment chains building their own catalogue in Uzbekistan. Custom colours, logo printing on device and cabinet, branded cartons and manuals, custom carton inserts, multi-language documentation, and OEM programs from low four-figure unit quantities with a 30-day DOA replacement SLA per order.

3. Contractor and System Integrator Programs

For fire protection contractors, system integrators and facility management groups in Tashkent running project pipelines. Project-matched device schedules, panel cause-and-effect pre-programming, BACnet and Modbus register maps, cloud account provisioning for the 705 monitors, commissioning briefings for the first project, and spares allocation held against the project programme.

4. Cross-Border Trader and Sourcing Agent Programs

For trading companies, sourcing agents and import brokers in Tashkent and Uzbekistan seeking a reliable Chinese source factory for fire protection products. Complete export solutions: EXW, FOB, CIF and DDP shipping terms, T/T or L/C payment handling, HS 8531 classification support, consolidated CE, RoHS, REACH, FCC and EN 54 documentation, neutral or custom packaging, localized manuals, and commission-based or volume-based partnership structures for long-term trade cooperation. Global partners, export trading companies and local distributors are welcome to contact the Wanlin export desk for exclusive-territory discussion.

5. Government, Municipal and Infrastructure Project Programs

For civil defence contractors, municipal facility departments, airport and rail operators and public-building authorities in Tashkent running compliance programmes. Site-matched device selection, pilot batches, consolidated submission dossiers, crew training for the first commissioning, and a five-year spare-parts window with a documented obsolescence path across multi-year maintenance contracts.

Frequently Asked Questions

Q: Which standards, certificates and national approvals ship with the WANLIN line?

A: The line is built to the standards approval bodies enforce: EN 54-7 smoke detectors, EN 54-5 heat detectors, EN 54-11 manual call points, EN 54-3 sounders, EN 54-23 visual alarm devices, EN 54-25 radio-linked components, EN 54-2 / EN 54-4 control and indicating equipment, EN 14604 residential smoke alarms, EN 50291 CO alarms and EN 50194 gas detectors, with CE marking under the Construction Products Regulation and UKCA for Great Britain, RoHS, REACH and FCC files, the UL 217 / UL 268 / UL 521 / UL 864 project path for the Americas, RCM for Australia and New Zealand, and SASO with SABER PCoC and SCoC, G-Mark, SNI, TISI, SIRIM, PS Mark, BFP, BIS, EAC, CCCF and SONCAP support where the market requires national approval. NIST-traceable calibration records ship per lot on instrumentation and on the A119-YW test aerosol. The certificate set, the declaration of conformity and the manual in the local language ship inside the carton for Uzbekistan.

Q: Can one supplier cover detection, control, signalling, instrumentation and test equipment on a corridor project?

A: Yes. The line covers photoelectric and ionization smoke detectors, A1R / A2S heat detectors, resettable and weatherproof manual call points, EN 54-3 and EN 54-23 sounder strobes, the WANLIN-860 and WANLIN-868D host platforms, WANLIN-770 pressure transmitters and gauges, ultrasonic and radar level sensors, the WANLIN-705 smart power monitoring device with residual current and arc fault detection, catalytic, infrared and electrochemical gas and CO detectors, the WANLIN-260 home package, the WANLIN-710 smart circuit breaker and the A119-YW detector tester. One purchase order, one certificate set, one spares list — which is what a handover pack and a lender's safeguard review both need.

Q: LoRaWAN, NB-IoT, 4G, 433 MHz or Wi-Fi — which one should a Tashkent project specify?

A: It depends on what you own and what you can power. An estate you control with an antenna position — a campus, an industrial park, a tank farm — runs LoRaWAN into the WANLIN-868D host, one gateway covering kilometres with multi-year battery life. Devices scattered across a city or a utility territory with no gateway to justify run NB-IoT for decade-long battery life, or 4G Cat-1 where mains power is available and the data rate matters. A single building that cannot be re-cabled runs 433 MHz RF interconnect with up to 40 devices and no subscription. Homes and small commercial units with an existing router run Wi-Fi on the WANLIN-260 package and the WANLIN-710 breaker. Permanent commercial and industrial sites add Ethernet with BACnet and Modbus to the building management system. Our export desk works through the selection with the partner before the schedule is priced.

Q: What technical support, training and documentation do partners in Tashkent receive?

A: System design and layout design support from the device schedule, wiring diagrams, configuration guides, testing procedures, commissioning and maintenance manuals and troubleshooting guides in the local language; installation, commissioning and maintenance training for partner crews on site or by video; remote and online support through the first commissioning; over-the-air firmware and software updates with change notification; and a spare-part, replacement-part and accessory supply programme with a five-year window and a documented obsolescence path, including battery replacement programmes sized to annual volume.

Q: How is equipment proven at handover and at the annual inspection?

A: The host platform exports its event log, the WANLIN-705 monitor exports per-circuit history, and the A119-YW tester tags each device by NFC or Bluetooth and generates the site-specific pass or fail report automatically — device ID, timestamp, stimulus channel and result per detector. The report exports by USB or cloud, so the facility manager receives it before the crew leaves site, and the test aerosol is non-flammable, HFC-free and residue-free with the safety data sheet in the shipment file.

Q: What are the lead times, minimum order quantities and warranty terms?

A: Sample cartons typically ship within 10-15 days and production project batches 28-35 days after approval. OEM and private-label programmes start from low four-figure unit quantities per model, and container-level mixed-model orders are quoted per destination. The line carries a 3-year limited warranty on detectors, panels and signalling devices (2-year on instrumentation and on the tester body), a 12-month warranty on battery packs, 30-day DOA replacement, and a five-year spare-parts window with a documented obsolescence path for tenders that require a long service-life commitment in Uzbekistan.

Q: Do you supply Belt and Road infrastructure projects directly, or only through local partners?

A: Both, by design. We supply the contractor or the developer directly where the project schedule requires factory-level engineering support, and we supply through the local distributor or importer who will carry the spares, the training and the warranty service afterwards. In practice the strongest programmes run together: the local partner holds the territory and the after-sales capability, and the factory holds the schedule, the documentation and the engineering. Wanlin is recruiting local partners across the corridors and does not appoint competing distributors in the same territory without discussion.

Q: Can trading companies and sourcing agents in Tashkent work with Wanlin?

A: Yes. We are a source factory supporting cross-border traders and import agents with EXW, FOB, CIF and DDP export terms, T/T and L/C payment handling, HS 8531 classification support, consolidated CE, RoHS, REACH, FCC and EN 54 documentation with national approval files where the market requires them, neutral or custom packaging, localized manuals, low minimum sample-carton orders and volume-based partnership pricing. Wanlin is recruiting global local partners, export trading companies and sourcing agents in Uzbekistan, and exclusive-territory discussions are open through the export desk.

Contact Wanlin: Start Your Fire Protection Products Sourcing Project

For wholesale pricing, sample carton requests, CE, RoHS, REACH, FCC and EN 54 documentation, NIST-traceable calibration records, BS 5839-1 / NFPA 72 reference packs, OEM and private-label customization, spares and consumables programs, and partnership discussions in Tashkent and Uzbekistan:

• Email: wanlinfirecontrol@163.com
• Export Hotline: +8613261677119
• Website: www.wanlinfire.com
• Shenzhen HQ: Wanlin Group, Building B, Building 1, Beisida Medical Device Building, 28 Nantong Avenue, Baolong Community, Baolong Sub-district, Longgang District, Shenzhen, Guangdong, China
• Markets: Southeast Asia, South Asia, Central Asia, the Middle East, Africa, Latin America and the Pacific — 24-hour response
• Global partner recruitment: distributors, importers, fire protection contractors, system integrators, electrical wholesalers, facility management groups, civil defence contractors, trading companies and sourcing agents welcome — exclusive-territory and OEM/ODM programs open for 2026-2027